CB300*6氯丁橡胶止水带

CB300*6氯丁橡胶止水带 咨询联络方式：***

3, water pressure is greater than 8m, horizontal and vertical deformation exceeds 30mm, the width of CB type water stop belt shall be less than 350mm
The thickness should not be less than 8mm;
4, the water pressure is not greater than 8m, the horizontal deformation is not more than 20mm, when there is no vertical deformation, the width of CB type water stop should not be less than 200mm, the thickness should not be less than 5mm.
In addition, when the size of the structural section is greater than 500mm, the width of the CB type water stop belt shall not be less than 300mm, and when the CB type water stop is bent, the turning radius of the belt shall not be less than 300mm. In the embedded rubber water stop belt products according to the standards of the waterstop GBl8173.2 - 2000 is the use of rubber with high elasticity and compression deformation, elastic deformation under various loads, and economical in embedded rubber water stop belt sealing to effectively prevent the fastening of building components Water Leakage, seepage, and play a buffer role, can be to ensure the service life of the building project. This product is mainly used for concrete cast in must be permanent deformation joints, such as canals, tunnels, export, dam, aqueduct and so on.

CB300*6氯丁橡胶止水带 咨询联络方式：***

中埋式橡胶止水带，这是一种主要用于在混凝土变形缝、伸缩缝等混凝土内部设置的止水带产品，具有以橡胶材料弹性和结构形式来适应混凝土伸缩变形的能力。本产品是利用橡胶的高弹性和压缩变形性，在各种荷载下产生弹性变形，从而起到紧固密封有效地防止建筑构件的漏水，渗水，并起到减震缓冲作用，可确保工程建筑物的使用寿命。二、用途及适应温度橡胶止水带主要用于混凝土现浇时必须设有的较久性变形缝内，如水渠、隧道引出口、挡水坝、输水渡槽等。中埋式橡胶止水带适应温度：普通型：-25℃- 60℃；耐寒型：-40*C- 60℃ 。三、分类1、中埋式橡胶止水带产品分类从材料选择来区分可分为中埋式橡胶止水带、中埋式PVC止水带、中埋式止水带接头和中埋式遇水膨胀止水带等。2、从结构形式上可分为CB型止水带和CP型止水带两种。四、选用标准我们对于此种橡胶止水带设计及选用标准： 在工程设计及施工选用过程中，CB型止水带的宽度及厚度应按以下条件确定:1、水压小于4m,水平和垂直变形量不超过10mm 时，止水带的宽度不宜小于200mm，厚度不宜小于5mm； 2、水压为4-8m，水平和垂直变形量不超过30mm时，CB型止水带的宽度不宜小于300mm，厚度不宜小于6mm； 3、水压大于8m,水平和垂直变形量超过30mm时，CB型止水带的宽度不宜小于350mm ,厚度不宜小于8mm； 4、水压不大于8m,水平变形量不超过20mm，当无垂直变形时，CB型止水带的宽度不宜小于200mm,厚度不宜小于5mm。除此之外，当结构断面尺寸大于500mm时，CB型止水带的宽度不宜小于300mm，当CB型止水带进行弯曲放置时，其转弯半径不得小于300mm。中埋式橡胶止水带产品标准按止水带GBl8173.2—2000是利用橡胶的高弹性和压缩变形性，在各种荷载下产生弹性变形，从而经济型中埋式橡胶止水带起到紧固密封有效地防止建筑构件的漏水，渗水，并起到减震缓冲作用，可确保工程建筑物的使用寿命。本产品主要用于混凝土现浇时必须设有的较久性变形缝内，如水渠、隧道引出口、挡水坝、输水渡槽等。

CB300*6氯丁橡胶止水带 咨询联络方式：***

Three, classification
1, buried rubber water stop product classification, from the choice of materials to distinguish, can be divided into buried rubber water stop belt, embedded PVC water stop belt, embedded type water seal joint and embedded water expansion water stop belt and so on.
2, from the structural form can be divided into CB type water stop belt and CP type water stop belt two.
Four, selection criteria
We design and choose the standard for this kind of rubber stop belt:
In the process of engineering design and construction selection, the width and thickness of CB type water stop belt shall be determined according to the following conditions:
1 、 the water pressure is less than 4m, the horizontal and vertical deformation is not more than 10mm
The width of the water stopping belt shall not be less than 200mm, and the thickness shall not be less than 5mm;
2, the water pressure is 4-8M, the horizontal and vertical deformation amount is not more than 30mm, the width of CB type water stop belt should not be less than 300mm, the thickness should not be less than 6mm;

CB300*6氯丁橡胶止水带 咨询联络方式：***